刚从Corona官网找了相应的PDF资料，里面说的居然和随产品附的说明书说法不太一样。具体如下。
Receiver and Transmitter Setup Instructions
By following these steps you will ensure your transmitter and receiver are properly setup and ready
to fly.
1. Turn the transmitter on and adjust your transmitter to PPM mode (not PCM), and then turn the
transmitter off.
2. Press and hold down the programming button on the transmitting module, then turn the transmitter
on. The LED on the module will flash between red and yellow indicating the transmitter is ready to
bind with a receiver.
3. Press and hold down the button on the receiver and connect the receiver to the battery. The LED
on the receiver will flash red twice indicating the receiver is in binding mode. Within a few seconds
the receiver LED will flash rapidly for a moment indicating that it has successfully bound to the
transmitter module and both are now communicating on the same channels. Turn off the transmitter
and receiver now.
Note: If the receiver did not flash rapidly then binding was not successful. Check that the transmitter
module is flashing Red/Green, then restart the receiver binding by removing the receiver battery for a
few seconds and then reapplying with the button pressed on it again. Binding is best done without any
servos connected but this is normally not necessary.
4. Check the normal system operation. Turn the transmitter on, when the module LED is yellow then
connect the receiver to the battery. The red LED on the receiver will be fully ON, indicating the
receiver is operating properly. Receiver LED will be OFF when there is no signal.
Note: The transmitter MUST be turned on BEFORE the receiver is connected to the battery, or else
the receiver will not initialize. This is also a best practice for RC model safety.
After following these steps to program your transmitter and receiver, both modules will continue to
operate together each time you use the modules without further binding.
If there is a need to reprogram your modules (adding another receiver) please follow these steps above
again.
100# afterdot
你直接用万能表测量接收机上随便一个通道的电压，就可以知道开机时的电压是否在说明书写的4.8V～6V工作电压以内，是否必须两次开机才能达到工作电压。我以前测试过V1版本大概低于3.7V,高于6.7V，这个接收机会保护性关机，所有舵机自动回复中位，只有电压恢复正常的工作电压以内，接收机才重新工作自动接收信号，不用二次开机。
我用的也是3PK，尝试按照规范开机方式先开控再开接收，很难一次成功连接，所以仔细阅读了说明书才发现，说明书上的顺序是先开接收机再开控，当时也感觉很古怪，不过按着做了，发现连接顺利很多，但是二次开接收机才能 ...
afterdot 发表于 09-2-24 14:08 http://bbs.rcfans.com/images/common/back.gif
你好，我的电调是F家低端的mc330cr
本帖最后由 afterdot 于 09-3-1 17:29 编辑
刚买了个国产的320A电调，按照正常开机顺序先开控再开接收机，一切正常，每次都顺利连上，没有任何问题了。看来Corona的接收机和好盈无刷电调的兼容性还不是很好，看来果真是电调捣鬼。好了，Corona 2.4G这下终于平反了，哈哈哈。犹豫中的兄弟可以考虑下手。
好帖。。学习了。。
JOHO你这人很不怎么样！人家在2.4G帖子里和开着FJ玩E-MAXX的帖子里 说的都很不错啊 ！可是你怎么说人家的人家怎么和你说话的！ 你不把人逼急了人家逼急了人家能和你说一样激进的话么 ？ 你反思下你自己吧
希望事情到此结束不要防碍大家畅所预言。如果每个人都像你这样谁都不要说话了 ！！
tonyshan007
我挺你，对于国产我也是有狠深的感情的
对以前的是不好
但是新推出的有个改进这是我们想看到的
国产 有些地方是不尽人意对于那些习惯了高级控的米人，就是垃圾
认为 4VF也比天9 通道多
现在的经济危机下都想出口但是又出不去
只能拉动内需来促进人民的生活水平
国内厂家推去新的产品 相对于以前的产品有狠大的改观 这就是正真的争气了
以价格来打造市场，卖的多了 才有资金去研发 测试
没米你能干什么？
吃饭都是问题 你还能玩模型~！！
别以为外国什么都好去听听“许四多”
让你明白什么是中国人~！！！
本帖最后由 AI 于 09-3-6 19:43 编辑
刚才仔细观察了我的车，发现长时间搁置后开机，电调风扇要过一会儿才能达到正常转速，但如果第二次开机立刻就能到达正常转速，应该是由于电调电源接入段并联了两颗电容有关，电池需要先给电容充电，估计此时电调供应 ...
afterdot 发表于 09-2-24 00:06 http://bbs.rcfans.com/images/common/back.gif
估计不是电容充电的问题,以偶以前车上使用大约1万5左右UF的电容(偶想这个容量和充电时间应该算不小了)配合普通FM接收和KO 2.4G接收再加上有刷和HY无刷的情况来看,在连接电池线的一瞬间也就是也许1秒左右,电容已经可以充完电,接完线正常去开接收就可以正常工作,不会出现类似与你那样的问题
为可每次也说什么：穷与富的分别？
穷有穷的方法玩RC，有自尊是对，但过份了就变自悲，每当有人提出疑问，就说有钱人不明？跟本不从基本思想学起，只想自圓其說！
最可悲是那些真正穷又想玩的人，给其他人误导，转了个大圈，钱花在教训上。
我有安捷伦的频谱仪可以用,要不要我给测测?
|
|