phonehe 发表于 23-8-5 20:12:56

xv02套用tt和xv01车壳新思路

后孔是通用的，不用改，在前避震架上装了个3D打印的平台，然后用魔术贴和车壳固定。实测还蛮牢靠的。如果想用车壳柱的话也简单，在这个3D打印的平台上打两个孔，螺丝固定车壳柱就行。
http://image.rcfans.com/pic/20230805/1691237537788136_551.jpg?x-oss-process=image/watermark,image_cGljLzIwMjExMDA2L29zc18xNjMzNTM0ODIxOTgzXzg2NF81MzNfNTYucG5n,t_50,g_se,x_20,y_20
http://image.rcfans.com/pic/20230805/1691237537795911_394.jpg?x-oss-process=image/watermark,image_cGljLzIwMjExMDA2L29zc18xNjMzNTM0ODIxOTgzXzg2NF81MzNfNTYucG5n,t_50,g_se,x_20,y_20

Jeah 发表于 23-8-5 21:22:22

有车壳柱移位套件

hnwv 发表于 23-8-5 21:48:50

直接都3D打印,不是更好用吗https://app.rcfans.com/public/emotion/face_heiha.png
http://image.rcfans.com/pic/20230805/1691243225019675_328.jpg?x-oss-process=image/watermark,image_cGljLzIwMjExMDA2L29zc18xNjMzNTM0ODIxOTgzXzg2NF81MzNfNTYucG5n,t_50,g_se,x_20,y_20
http://image.rcfans.com/pic/20230805/1691243225021350_638.jpg?x-oss-process=image/watermark,image_cGljLzIwMjExMDA2L29zc18xNjMzNTM0ODIxOTgzXzg2NF81MzNfNTYucG5n,t_50,g_se,x_20,y_20

墨染 发表于 23-8-5 22:09:04

都有点逊https://app.rcfans.com/public/emotion/face_wangchai.pnghttps://app.rcfans.com/public/emotion/face_wangchai.pnghttps://app.rcfans.com/public/emotion/face_wangchai.png
http://image.rcfans.com/pic/20230805/1691244527102832_289.jpg?x-oss-process=image/watermark,image_cGljLzIwMjExMDA2L29zc18xNjMzNTM0ODIxOTgzXzg2NF81MzNfNTYucG5n,t_50,g_se,x_20,y_20
http://image.rcfans.com/pic/20230805/1691244544199717_677.jpg?x-oss-process=image/watermark,image_cGljLzIwMjExMDA2L29zc18xNjMzNTM0ODIxOTgzXzg2NF81MzNfNTYucG5n,t_50,g_se,x_20,y_20

danity 发表于 23-8-5 23:44:48

Tb上有卖打印的移位件，不过不够精准，与实际孔位误差1毫米左右，弃用了

phonehe 发表于 23-8-6 15:33:04

楼上各位八仙过海，长见识了

柯大爷丶 发表于 23-8-7 10:55:27

高度怎么调呢 往上垫？

世界拉力锦标赛 发表于 23-8-7 14:23:31

还有好办法吗

fly164825 发表于 23-8-7 17:32:39

世界拉力锦标赛 发表于 2023-08-07 14:23
还有好办法吗

车壳多打一对孔就得了

世界拉力锦标赛 发表于 23-8-7 21:45:37

fly164825 发表于 2023-08-07 17:32
车壳多打一对孔就得了

孔太多也不好啊
页: [1] 2
查看完整版本: xv02套用tt和xv01车壳新思路