美美美食家 发表于 23-7-15 23:00:55

baja改装新思路，大轴离合支架装小轴离合杯

原厂小轴离合支架和小轴大齿板暴力玩会融化甚至断
http://image.rcfans.com/pic/20230715/1689432480727666_351.jpg?x-oss-process=image/watermark,image_cGljLzIwMjExMDA2L29zc18xNjMzNTM0ODIxOTgzXzg2NF81MzNfNTYucG5n,t_50,g_se,x_20,y_20
大轴承这一套装AK离合杯只能用19到24t，为了玩17t所以我拿C4加厚大齿板和C4大轴承支架改了小轴离合杯
http://image.rcfans.com/pic/20230715/168943286969767_77.jpg?x-oss-process=image/watermark,image_cGljLzIwMjExMDA2L29zc18xNjMzNTM0ODIxOTgzXzg2NF81MzNfNTYucG5n,t_50,g_se,x_20,y_20
http://image.rcfans.com/pic/20230715/1689432869699959_571.jpg?x-oss-process=image/watermark,image_cGljLzIwMjExMDA2L29zc18xNjMzNTM0ODIxOTgzXzg2NF81MzNfNTYucG5n,t_50,g_se,x_20,y_20
需要用一颗6002和6201轴承，为什么不是两颗6201继续往下看
http://image.rcfans.com/pic/20230715/1689432879608325_488.jpg?x-oss-process=image/watermark,image_cGljLzIwMjExMDA2L29zc18xNjMzNTM0ODIxOTgzXzg2NF81MzNfNTYucG5n,t_50,g_se,x_20,y_20
两颗6201放里面会超高，螺丝锁离合支架时会锁在轴承上锁不到大齿板上。离合支架会上下移动，6201负责让离合杯转起来，6002负责顶住小齿防止小齿和离合杯往里滑卡离合器上
http://image.rcfans.com/pic/20230715/1689432939606565_155.jpg?x-oss-process=image/watermark,image_cGljLzIwMjExMDA2L29zc18xNjMzNTM0ODIxOTgzXzg2NF81MzNfNTYucG5n,t_50,g_se,x_20,y_20
http://image.rcfans.com/pic/20230715/1689432939724326_376.jpg?x-oss-process=image/watermark,image_cGljLzIwMjExMDA2L29zc18xNjMzNTM0ODIxOTgzXzg2NF81MzNfNTYucG5n,t_50,g_se,x_20,y_20
最后装好，还需要打磨一下大齿的盖板因为是加厚大齿板
http://image.rcfans.com/pic/20230715/1689433088218548_327.jpg?x-oss-process=image/watermark,image_cGljLzIwMjExMDA2L29zc18xNjMzNTM0ODIxOTgzXzg2NF81MzNfNTYucG5n,t_50,g_se,x_20,y_20
http://image.rcfans.com/pic/20230715/1689433088220905_888.jpg?x-oss-process=image/watermark,image_cGljLzIwMjExMDA2L29zc18xNjMzNTM0ODIxOTgzXzg2NF81MzNfNTYucG5n,t_50,g_se,x_20,y_20

pizil502 发表于 23-7-27 21:23:35

直接换个金属件不行吗

美美美食家 发表于 23-7-27 22:39:22

pizil502 发表于 2023-07-27 21:23
直接换个金属件不行吗

大轴离合杯齿最小是19／55改了小轴离合杯之后最小能用到17／57

睿rrrrrrrrr 发表于 23-7-28 22:43:27

可以可以
页: [1]
查看完整版本: baja改装新思路，大轴离合支架装小轴离合杯