1/10前驱十代思域 S02E01 装配前的准备
这周到货了各长度的调节臂码来减轻后轮内八字image.rcfans.com/data/appbyme/upload/image/202004/02/pYJBL4J6RBXz.jpg
然后开始粘接底盘，沿着左侧轮廓用直尺定位
image.rcfans.com/data/appbyme/upload/image/202004/02/YbG00po2CVFK.jpg
配合大力钳，使用914胶水粘接
image.rcfans.com/data/appbyme/upload/image/202004/02/hvlQJh7LZ2gr.jpg
image.rcfans.com/data/appbyme/upload/image/202004/02/hGcgvdSdlW0s.jpg
切割掉不需要的二楼板
image.rcfans.com/data/appbyme/upload/image/202004/02/ApzTRyQGPY5o.jpg
后面的凹槽放置电池，在后排座椅后方
image.rcfans.com/data/appbyme/upload/image/202004/02/ya4hGkakmSk3.jpg
image.rcfans.com/data/appbyme/upload/image/202004/02/hzZ0R2CYWWYe.jpg
切割车门轴套
image.rcfans.com/data/appbyme/upload/image/202004/02/u7FzNtfEfELO.jpg
塞进车门轴孔，增加强度
image.rcfans.com/data/appbyme/upload/image/202004/02/M5ewJEmGpNtO.jpg
试装配一下
image.rcfans.com/data/appbyme/upload/image/202004/02/9HAXqGIrEyuC.jpg
假组合
image.rcfans.com/data/appbyme/upload/image/202004/02/taUcfmhcNrss.jpg
image.rcfans.com/data/appbyme/upload/image/202004/02/RBDffyF3nN4d.jpg
image.rcfans.com/data/appbyme/upload/image/202004/02/07WmsdIVF9TU.jpg
image.rcfans.com/data/appbyme/upload/image/202004/02/YN6SxP8zGddA.jpg
image.rcfans.com/data/appbyme/upload/image/202004/02/mdWYTC14TnoH.jpg
车窗采用透明树脂打印，目前假组合完毕，准备用刻线刀刻出车身接缝细节
image.rcfans.com/data/appbyme/upload/image/202004/02/9YjwDxj8Hamy.jpg
image.rcfans.com/data/appbyme/upload/image/202004/02/sN8tu6CqtS5Q.jpg
image.rcfans.com/data/appbyme/upload/image/202004/02/SfwGFcYgDOvH.jpg
image.rcfans.com/data/appbyme/upload/image/202004/02/zwWCWWctwNUL.jpg
image.rcfans.com/data/appbyme/upload/image/202004/02/Js2232hlXWU2.jpg
大哥牛b 调节了下避震预压量
image.rcfans.com/data/appbyme/upload/image/202004/02/UsJia28aXWCO.jpg
image.rcfans.com/data/appbyme/upload/image/202004/02/hHAPa45i2GRn.jpg
论坛里到底有多少大神。。
厉害了 思域车主路过
牛逼，为啥不做两厢的TYPE-R
顶一个。。同十代车友 非常厉害 不喜欢那种设备堆积在一起 套个壳的车
页:
[1]
2