黑山羊 发表于 19-6-15 18:21 static/image/common/back.gif
图片，几张
拍点过程才有意义
加油，持续关注，希望你能成功！
有没有人和楼主一样的想法，我又四根车桥和八个轮胎http://image.rcfans.com/data/appbyme/app/data/phiz/default/03.pnghttp://image.rcfans.com/data/appbyme/app/data/phiz/default/03.pnghttp://image.rcfans.com/data/appbyme/app/data/phiz/default/03.png
发几张目前进度，最后一张是我用3D打印机前后分动箱。
http://image.rcfans.com/data/appbyme/upload/image/201906/21/DSoc3q6DxOGq.jpg
http://image.rcfans.com/data/appbyme/upload/image/201906/21/mpGFhVgXRjP3.jpg
http://image.rcfans.com/data/appbyme/upload/image/201906/21/Bc4xfMgqLdr2.jpg
http://image.rcfans.com/data/appbyme/upload/image/201906/21/BOCOn1PSMdQp.jpg
http://image.rcfans.com/data/appbyme/upload/image/201906/21/OvhZSKzp5zHz.jpg
底盘系统结束了，缺点避震太硬了，等所有设备都上车了再想办法调整避震弹簧的软硬。
http://image.rcfans.com/data/appbyme/upload/image/201906/23/yYY5T5Vs5Xkp.jpg
http://image.rcfans.com/data/appbyme/upload/image/201906/23/siHBHkMA3r2v.jpg
http://image.rcfans.com/data/appbyme/upload/image/201906/23/Y9SuQd4DHMVs.jpg
http://image.rcfans.com/data/appbyme/upload/image/201906/23/LpqmNgFyIjkS.jpg
http://image.rcfans.com/data/appbyme/upload/image/201906/23/8oYKkwAkPPeg.jpg
建议把拉杆换成刀臂，原车的拉杆一加油轴效应特别大
西安王冰 发表于 19-6-23 00:46 static/image/common/back.gif
建议把拉杆换成刀臂，原车的拉杆一加油轴效应特别大
不懂啥意思！啥事刀臂啊http://image.rcfans.com/data/appbyme/app/data/phiz/default/37.png
今天把前后转向系统装好了，由于前后轴太远所以就采用俩舵机来分别控制前后转向轴了
http://image.rcfans.com/data/appbyme/upload/image/201906/24/mjQuS5iXhH2g.jpg
http://image.rcfans.com/data/appbyme/upload/image/201906/24/nDS4QLblhqbM.jpg
http://image.rcfans.com/data/appbyme/upload/image/201906/24/gTIS5M0VUsKU.jpg
http://image.rcfans.com/data/appbyme/upload/image/201906/24/0yqLuPMFdApy.jpg
http://image.rcfans.com/data/appbyme/upload/image/201906/24/2MAL2EYx0yyj.jpg
这是在浪费钱啊
hanzc520 发表于 19-6-24 22:21 static/image/common/back.gif
不懂啥意思！啥事刀臂啊
参考后直桥短卡
|
|