sh04882 发表于 18-10-27 21:16:08

一个冷门拖头的制作过程，完成90%

从有想法开始做到今天已经过去大半年了，先上图，各位客观姥爷多给点意见。
http://image.rcfans.com/data/appbyme/upload/image/201810/27/g23QbN1qOH5T.jpg
http://image.rcfans.com/data/appbyme/upload/image/201810/27/eTNPaL4gH1Rz.jpg
http://image.rcfans.com/data/appbyme/upload/image/201810/27/wn5E6DQh76JR.jpg
http://image.rcfans.com/data/appbyme/upload/image/201810/27/FbF7vMEcnhy9.jpg
http://image.rcfans.com/data/appbyme/upload/image/201810/27/y7zXKwtQRKs5.jpg
http://image.rcfans.com/data/appbyme/upload/image/201810/27/MSChE7NgYrao.jpg
http://image.rcfans.com/data/appbyme/upload/image/201810/27/g3ZPwLFGq7OA.jpg
http://image.rcfans.com/data/appbyme/upload/image/201810/27/M11gBLXowUtW.jpg
http://image.rcfans.com/data/appbyme/upload/image/201810/27/iMbCL4KJjY8E.jpg
http://image.rcfans.com/data/appbyme/upload/image/201810/27/npskYdWBpLfZ.jpg

sh04882 发表于 18-10-27 21:16:53


http://image.rcfans.com/data/appbyme/upload/image/201810/27/qngcLnEsFdvG.jpg
http://image.rcfans.com/data/appbyme/upload/image/201810/27/UKSeEaJZHo5A.jpg
http://image.rcfans.com/data/appbyme/upload/image/201810/27/V7pV1P4t1Ph5.jpg
http://image.rcfans.com/data/appbyme/upload/image/201810/27/RnZ8T4WFvS7b.jpg
http://image.rcfans.com/data/appbyme/upload/image/201810/27/cCh07poGR1xF.jpg

sh04882 发表于 18-10-27 21:17:39


http://image.rcfans.com/data/appbyme/upload/image/201810/27/sBiTqdElFyJA.jpg
http://image.rcfans.com/data/appbyme/upload/image/201810/27/9odkcenSQ0Rs.jpg
http://image.rcfans.com/data/appbyme/upload/image/201810/27/UdrBStqqvHaX.jpg
http://image.rcfans.com/data/appbyme/upload/image/201810/27/knCUZGkU45Sh.jpg
http://image.rcfans.com/data/appbyme/upload/image/201810/27/mQYgz4jsQ4Cj.jpg

maxuesong 发表于 18-10-27 21:24:33

打印的强度够不够啊

sh04882 发表于 18-10-27 21:39:13

maxuesong 发表于 18-10-27 21:24 static/image/common/back.gif
打印的强度够不够啊

承重的地方厚度要2毫米以上，装饰的地方一毫米以上，强度放在这种低速的模型上没有问题，

帕布 发表于 18-10-27 23:28:28

上色

sh04882 发表于 18-10-28 07:21:26

帕布 发表于 18-10-27 23:28 static/image/common/back.gif
上色

嗯，底盘用自喷漆上色
http://image.rcfans.com/data/appbyme/upload/image/201810/28/l2TREgv0FShX.jpg
http://image.rcfans.com/data/appbyme/upload/image/201810/28/qkyA6sqVtW1z.jpg

guanyong 发表于 18-10-28 08:48:35

不得了http://image.rcfans.com/data/appbyme/app/data/phiz/default/07.pnghttp://image.rcfans.com/data/appbyme/app/data/phiz/default/07.pnghttp://image.rcfans.com/data/appbyme/app/data/phiz/default/07.png

奔跑的蜗牛888 发表于 18-10-28 09:09:34

这个前后轮胎直径不一样，转速能同步吗？

sh04882 发表于 18-10-28 10:12:46

奔跑的蜗牛888 发表于 18-10-28 09:09 static/image/common/back.gif
这个前后轮胎直径不一样，转速能同步吗？

用分动箱里的两个齿数不同的齿轮调整转数，两个齿数比和两个轮子直径成正比
页: [1] 2
查看完整版本: 一个冷门拖头的制作过程，完成90%